Euro Synthetic Oils - MPT Additives

MPT ENGINE TREATMENTThis unique formula is recommended for use in all four-cycle engines (gasoline and diesel) with either synthetic or petroleum based motor oils. MPT Engine Treatment clings to internal engine parts thus reducing friction and wear. The formula, with regular use, will significantly extend engine life. Smoother and quieter operation will result in increased efficiency for better fuel mileage, easier starting, more power and better performance. Use MPT Engine Treatment at every oil change. Add two ounces per quart of motor oil for the initial treatment. Subsequent treatments require a minimum of one ounce per quart of motor oil. MPT Engine Treatment will not void new car warranties. It can be used as a Zinc Dialky Dithophosphate (ZDDP) substitute in API-approved motor oils, providing the long-term protection necessary in pre-1989 cars with non-roller lifters or today’s high performance engines

Extends Engine Life

Increases Fuel Mileage

Reduces Heat & Friction

Engine Will Run Smoother & Produce More Power

Add as a ZDDP Substitute in API-Approved Motor Oils

Using MPT® Engine Treatment as a ZDDP Substitute

Until now, motor oil companies have used Zinc Dialky Dithophosphate (ZDDP) to reduce wear in camshafts and lifters. The use of ZDDP, however, shortens the life of your vehicle’s emissions system. The Environmental Protection Agency (EPA) has mandated that the zinc level in motor oil be reduced to near zero, due to the harmful effects on catalytic converters and emissions systems. American Petroleum Institute (API) approved motor oils currently contain less than one tenth of a percent of ZDDP – a mere fraction of what was previously allowed – creating a serious deficiency in engine protection. Without ZDDP, modern day performance engines, as well as older engines with flat tappet valves, can experience premature wear, higher operating temperatures and premature engine failure because there is nothing to coat moving engine parts and prevent metal-to-metal contact. Additionally, manual transmissions and gearboxes where the manufacturer specifies the use of motor oil for lubrication would require a ZDDP substitute.

During the first few thousand miles of engine use, oils with a small amount of ZDDP provide sufficient break-in protection. ZDDP reduces wear, but can actually increase friction and reduce fuel mileage. Additionally, API approved oils have low levels of ZDDP and do not provide the long-term protection necessary in pre-1989 cars with non-roller lifters or today’s high performance engines. Supplementing your oil with the molybdenum/PTFE formulation of MPT Engine Treatment will provide superior protection by eliminating metal-to-metal contact. MPT Engine Treatment is guaranteed to eliminate premature deterioration of flat tappet valves and high performance motors after the initial break-in period by clinging to internal engine parts, thus reducing friction and wear. After a 3,000-5,000 mile break-in period, simply add 2 ounces of MPT Engine Treatment for every quart of motor oil (do not overfill). Subsequent oil changes require about one ounce per quart of motor oil.

MPT GEAR TREATMENT This unique formula is recommended for use in all manual transmissions, gearboxes, transfer cases or differentials with either synthetic or petroleum based gear oils. MPT Gear Treatment clings to internal gearbox parts thus reducing friction and wear. The formula, with regular use, will result in increased gearbox life. Smoother and quieter operation will result in increased efficiency for better fuel mileage, easier shifting, more power and better performance. Use MPT Gear Treatment as a friction modifier/slip additive to prevent gear chatter and provide smooth operation of clutch-type limited-slip differentials. Add only enough to prevent the chatter. Adding too much could make the plates/clutches too slippery. Add MPT Gear Treatment at every oil change. For the initial application, 2-3 ounces per quart of gear oil should be added. Subsequent applications require 1-2 ounces per quart of gear oil. MPT Gear Treatment will not void new car warranties.

Extends Transmission Life

Reduces Heat & Friction

For Smoother, Easier Shifting

MPT FUEL SYSTEM CLANSE Powerful polyether amine chemistry removes contaminants from gasoline fuel injectors, intake valves, pollution control valves, combustion chambers, and carburetors without the use of harmful solvents such as alcohol, toluene, and acetone that can damage the fuel system. The major brands of gasoline do not contain detergents that will remove fuel system deposits. These deposits steal power and decrease fuel mileage. MPT Fuel System Cleanse cleans and lubricates upper cylinders and pollution control valves. For peak efficiency and best performance, use MPT Fuel System Cleanse regularly. One 12 ounce bottle will quickly clean an entire fuel system. It can be added to 12-24 gallons of gasoline. For best results, add one bottle every 3,000 miles. MPT Fuel System Cleanse can also be added in small amounts at each fill up – add approximately 1 once per 6-7 gallons of fuel.

Maintains Peak Efficiency

Increases Fuel Mileage

Engine Will Run Smoother & Produce More Power

MPT® Twelve Pump Spray Formula Multi-Purpose Molybdenum/PTFE Lubricant and Penetrant Cleans and protects • Penetrating formula with rust inhibitors • Stops binding, sticking and squeaking • Environmentally-friendly pump spray bottle Use MPT Twelve Pump Spray Formula for larger area applications where precision delivery is not required. MPT Twelve is compatible with oils and greases and can be applied to roller guides, sliding door tracks, cogs, pulleys, bicycle and motorcycle chains, etc. Specially formulated for easy dispersal, MPT Twelve Pump Spray Formula is available in a special four ounce pump spray bottle that is convenient and easy to use.

MPT® Twelve

Multi-Purpose Molybdenum/PTFE
Lubricant and Penetrant

Ideal For Hundreds Of Uses

Around The House, In The Workshop And Garage, Even Outdoors!

MPT Twelve is the longest lasting lubricant and penetrant available. It protects against rain, snow, ice, heat, humidity, dust and salt-spray to prevent rust and binding, as its special molybdenum/PTFE (polytetrafluoroethylene) formula penetrates, cleans and lubricates, leaving a long-lasting protective film.

View Coefficient Of Friction Testing

MPT® Twelve Concentrated Formula - Snub NoseTube - 3 Pack - ½ Oz. Tubes

Multi-Purpose Molybdenum/PTFE Lubricant and Penetrant. This penetrating formula with rust inhibitors, stops binding, sticking and squeaking and cleans and protects. You should use MPT Twelve Concentrated Formula in critical applications where service failures are not acceptable. MPT Twelve is compatible with oils and greases, and can be applied to precision bearings; nuts and bolts; indoor and outdoor locks, latches and hinges; power tools; small motors; computers and printers; lawn mower, snowblower, bicycle and motorcycle cables; etc.